Thermador HPCN36NS Installation Manual Page 16
- Page / 63
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
English 14
1. Remove junction box channel covering the wires (see
Figure 9 on page 11).
2. Remove circular knockouts (Figure 9 on page 11).
3. Connect the blower’s Molex plug connector to the
connector present inside the hood, as shown in
Figure 16.
4. Install 1” (25.4 mm) conduit connector in junction box.
5. Run black, white, and green wires (#12 AWG) in 1”
(25.4 mm) conduit from the power supply to the
junction box.
6. Connect the power supply wires to the hood wires in
the following order: black to black, white to white, and
green wire to green ground screw on chassis. Use
spring type wire nuts.
• Wire nuts should be spring type wire nuts rated for
a minimum of two (2) #18 gauge wires and
maximum of four (4) #14 gauge wires, UL & CSA
rated to 600V and 302°F (150°C).
7. Reinstall the junction box channel.
Wiring the Hood with a Remote Blower
Depending on preference and ducting situation, these
blowers can be mounted on the roof or exterior wall of the
home. An exterior installation may be more appealing to
reduce noise in the kitchen.
1. Remove junction box channel covering the wires (see
Figure 9 on page 11).
2. Remove circular knockouts (Figure 9 on page 11).
3. Install 1” (25.4 mm) conduit connectors.
4. Run black, white, and green wires (#12 AWG) in 1”
(25.4 mm) conduit from the power supply to the
junction box.
5. Connect the power supply wires to the hood wires in
the following order: black to black, white to white, and
green wire to green ground screw on chassis. Use
spring type wire nuts.
• Wire nuts should be spring type wire nuts rated for
a minimum of two (2) #18 gauge wires and
maximum of four (4) #14 gauge wires, UL & CSA
rated to 600V and 302°F (150°C).
6. Connect the “pigtail” to the connector inside the
junction box.
7. Run five (5) #14 AWG wires in 1” (25.4 mm) conduit
from the remote blower to the second conduit
connector.
8. Connect the remote blower to the pigtail wires as per
Figure 18. Connect the remote blower green (ground)
wire to the ground screw in the junction box. Refer to
the blower installation instructions for further wiring
details.
9. Reinstall the junction box channel.
Figure 16: Wiring the Hood with an Integral Blower
measurements in inches (mm)
Figure 17: VTR1330 Remote Blower
From Hood
From Hood
From Hood From Blower
From Blower
From Blower
19
7/
8
"
(505)
2
1/
8
"
(54)
10 "
(254)
2
1/
8
"
(54)
20
3/
4
"
(527)
12
7/
8
"
(327)
12
1/
8
"
(308)
6
1/
2
"
(165)
1
7/
8
"
(48)
13
5/
8
"
(346)
dia. 9
7/
8
"
(251)
Figure 18: Wiring the Hood with a Remote Blower
SPEED 1
SPEED 2
SPEED 3
NEUTRAL
RD
BU
BN
WH
SP4
GROUND
N
SP1
SP2
SP3
Brown
Brown
Brown
Green/Yellow
Green/Yellow
Green/Yellow
White
White
White
Red
Red
Red
Blue
Blue
Blue
Orange
Orange
Orange
WH / BC / BL (16 AWG)
BK / N / NE (16 AWG)
120V, 60HZ, 20A
POWER SUPPLY
L1NT1T2S3
- INSTALLATION MANUAL 1
- MANUEL D'INSTALLATION 1
- MANUAL D INSTALACIÓN 1
- Table of Contents 2
- IMPORTANT SAFETY INSTRUCTIONS 3
- Advance Planning 5
- General Information 6
- Installation Preparation 7
- Ductwork Preparation 8
- English 7 9
- Electrical Requirements 10
- Hood Transition 10
- Installation Instructions 11
- Back Wall Preparation 12
- Hanging the Chimney Hood 13
- Wire Connection 14
- Blower Motor Installation 15
- From Hood 16
- From Hood From Blower 16
- From Blower 16
- L1NT1T2S3 17
- Chimney Extension 18
- Installation (optional) 18
- Installing Grease Trays and 20
- Before Calling Service 21
- Table des Matières 22
- Sécurité 23
- Planification préalable 25
- Renseignements généraux 26
- Dimensions générales 26
- Préparation de l’installation 27
- Préparation du conduit 28
- Française 7 29
- Exigences électriques 30
- Raccord pour la hotte 30
- Instructions d’installation 31
- Préparation de la cloison 32
- Branchement des câbles 34
- Installation du ventilateur 35
- Installation des plateaux à 40
- Liste de vérification à 41
- Índice de Materias 42
- Seguridad 43
- Planificación avanzada 45
- Información general 46
- Dimensiones totales 46
- Factores a tener en cuenta 47
- Preparación del conducto 48
- Español 7 49
- Exigencias eléctricas 50
- Junta de la campana 50
- Instrucciones de instalación 51
- Preparación de la pared 52
- Cómo colgar la campana con 53
- Conexión de los cables 54
- Instalación del motor del 55
- Cómo instalar las bandejas 60
- Antes de solicitar servicio 61
- Lista de chequeo para el 61
- THERMADOR 63
Related products and manuals for Cooker hoods Thermador HPCN36NS
Cooker hoods Thermador HMWN48FS User Manual
(29 pages)
(29 pages)
Cooker hoods Thermador HMCB36WS User's Guide
(12 pages)
(12 pages)
Cooker hoods Thermador HMCN42FS User Manual
(32 pages)
(32 pages)
Cooker hoods Thermador HPWB30FS User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.606 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals